37€94
The product is compliant and the service is fast.
The delivery was a problem because of the driver, but LDLC reacted immediately to solve the problem: efficient service...
Thank you very much!
Very good graphics card support. I recommend it if you have a fairly massive GCU to avoid damaging your motherboard because of the weight.
Ingenious, well thought out, and most importantly plays its part in supporting the graphics card. My Gigabyte 2070 Super with 3 fans started to bend under its weight over time. Large and heavy card (2.5 PCI slots).
Ideally to be installed from day 1. Here I hope it will straighten the graphics card PCB over time.
I had a bit of trouble installing it and had to cut off part of the vertical rod because although my tower is very high (Zalman GS1000), there was a reinforcing bar in the lower quarter that was in the way. So I leaned on this bar.
I also added two nuts to secure the two vertical rods that slide into each other, the only screw/nut set at the bottom seemed a bit insufficient.
Once adjusted, this support is very well anchored in the tower and does not move anymore. The two parts to block the graphics card play their role well, once blocked, the graphics card can not move.
In short, an indispensable device when you have a big graphics card.
You can feel the quality of the product, everything is done to the hundredth of a millimetre, just magnificent, everything is already planned, produced to support a CG and a CPU. assembly time barely 10 minutes
Unfortunately it doesn't fit in a Corsair Carbide Series 175R, because of the power supply compartment that prevents the FixCard from being wedged in. I thought the rods would be more retractable, but never mind.
If you're buying, be extra careful about how much room your case gives you in height, and also be careful about how wide your graphics card is. Allow about 3-4 cm of space between your connected CG and the side panel.
I'm saving this because it might be useful later, but too bad. My RTX 3070 seems to be pretty well fixed for now...
Very good product with a solid and qualitative appearance. I did remove one star as it is not possible to shift the pads for the graphics card on the "case depth" axis. My graphics card is not as big as the latest one you can find nowadays, the ventirad is so strong, it forces to install the card holder stuck on its right side and thus at the very end of the graphics card. A small horizontal rail to move the pads along the graphics card would make this product perfect for a future release.
Otherwise, the whole thing tightly packed into the case really gives a feeling of reinforcing the installation.
not suitable for a 450 noctis nzxt due to power supply cover location, see compatible cases, sawing a slide cleanly fits without a hitch, no fixing problems, graphics card well maintained, processor fan levels maintained without worries, just see over time if the rubber strap deforms
This product is very good for moving your PC often, but don't expect a miracle product either...
I can mention some negative points like the difficulty to install it or the fact that it doesn't really support the graphics card (because of the holes not present on the whole slide which restricts some places)
On the other hand, it supports my rather heavy ventirad (pure rock) very well
I don't understand the other comments indicating that they have problems putting the brackets/skids in place that are in contact with the CG.
You really need to put them as shown in the photos and the manual, in "duckbill open" mode: that way they are in the stop and can't open more.
The assembly is easier if you find another pair of arms. The product is really well designed to adapt to many configurations: in my case the bottom fan was a problem, but no problem, just move closer to the wall and the skids were long enough to touch the CG
The only drawback will be visual... I'm looking for ideas to dress up this vertical bar but the possibilities are numerous.
The idea is good, but the realisation is not quite complete.
No matter how much you tighten the brackets to raise the CG, they don't keep their position. For my 980 I used the strap provided to hold the fan to suspend the CG. The metal used is not hard enough and the fixcard holder is easily deformed.
I had installed the FixCard in my be quiet! Dark Base Pro 900 (rev 1) case. My GPU is an ASUS GeForce GTX 1060 ROG STRIX-GTX1060-O6G-GAMING.
Well, ok, considering the size of the case I took a risk. I also had a hard time getting it to fit, the FixCard was really just the right length. I had a lot of trouble getting my GPU to fit. I read the instructions several times, and watched the video several times... and tried again several times. Nothing helped, there was always a little bit of play that appeared after tightening, so that the card was finally not (or very little) retained.
My personal opinion (which is only mine): I have the impression that the whole problem comes from the clamping system of the tabs. There is only one screw that holds the bracket in place on the rail and at a certain angle. Well, at least in my case, it doesn't work. After tightening, the legs stay in their position on the rail but rotate a little, giving some play. Then ... I also suspect that the shape of the GPU prevents the legs from tightening properly. Again, my personal opinion: I think that a system with 2 screws should have been used to keep the bracket in the right angle (so that it can't rotate), *then* slide the bracket on the rail as close as possible to the card and maintain this position by tightening a 3rd screw.
I'm not sure about this, but I'm still very doubtful about the clamping system of the tabs.
This product does what I bought it for, which is to hold a large graphics card (GeForce GTX 1070 Ti) to prevent it from bending and/or damaging the PCI-Express slot it is inserted in.
The downside is that the tool itself takes up a lot of space, which can get in the way if the case is quite full.
You also have to be careful when mounting to tighten the screws so that the whole thing is solid, and to find the right position so as not to interfere (cable routing, card position, case closure, etc.). The documentation would benefit from being clearer.
Certainly a good product as the finish seems very good, but unfortunately the product is impossible to install in a Corsair Carbide 400C.
Too bad for me.
Let's hope that the manufacturer finds a suitable product for this type of case because the basic idea is very good.
Used in a cooler master cosmos II case it installs without any problem but the two clamps that are supposed to support the graphics card have no resistance with this clamping system.
I have scrupulously respected the assembly instructions and the video tutorial but in one way or another, these clamps are useless as they are unable to support the weight of my graphics card (big heavy 1080 ti card).
Well thought out, the whole thing is perfect, adjustable in all directions, but the only downside is that the GPU support spatulas are useless, the knobs to tighten on each side of the main bar are made of plastic so your GPU better be stuffed with feathers or cotton for the ineffective support to be of any use.
Good product overall, minimal packaging, easy to recycle as a result. The product is as described and relatively easy to install.
The only downside is that I have an ATX IN WIN 101 TUF GAMING case and the tilteek with the two vertical bars does not fit. I had to remove one of the bars, and even then, it doesn't fit completely, so I had to improvise. So I'm reducing the score a bit
This is a must have item for any home or pro setup. In fact, I just wonder how I managed to mount so many PCs without having this attachment beforehand ^^.
I'm sure you'll find it very useful to have this item on your site.
I installed this kit, everything is perfect, the telescopic bar is fixed well etc except that.....
the supports well they support kedal, in spite of a tightening of warrior on the wheels that does not support the weight of my two gtx mars 760..... resulat no utility, they would have put screws and spacers in metal rather than plastic that would have changed everything ...... ridiculous
Very useful to keep a graphics card in place whatever the model, but generally recommended for large cards over 25cm because at the end it hangs down and may be damaged by vibrations.
Bought to essentially support an Asus ROG STRIX-GTX1050TI in a Fractal Design Define R3 case, it does the job.
However, beware of the type of case the beast will be mounted in. The same goes for the CG, the placement of the flanges was done to the millimeter on my 1050 because the only usable spot is between the PCie power connector and the rear fan of the card.
The only usable spot is between the PCie power supply connector and the rear fan of the card (the flange protrudes on both, I advise to connect the power supply and to shift the slide over it in order to leave the fan blades free)
I'm not sure if this is a good idea or not, but I'm not sure if it's a good idea to have the fan on the board, and I'm not sure if it's a good idea to have the fan on the board.
I'm taking off one star because of the price, the tool is certainly modular and easy to assemble but it remains a "piece of junk" that I find relatively expensive. 10 € less would not seem unreasonable to me.
Fast delivery.
Doesn't work with my configuration on a HAF X. Not easy to explain in words, but nothing falls where it should, at least not without tinkering and/or forcing some elements unnecessarily. Too bad, it was a good idea.
Purchase to hold a GTX 1070 Strix correctly and not to lean on the motherboard.
Very solid structure.
Aesthetically it's not bad with the little laser cut that goes well.
The support of the graphics card on rubber is toop.
I'm very pleased with the quality of the product and the service. It's a great product and I'm very pleased with the quality of the product.
Good product, solid and easy to assemble. On the other hand, with a good gamer config it's a pain. I have a large tower (HAF style) with a be quiet! Dark Rock PRO 3 ventirad and a 1080 graphics card from MSI, impossible to position the bracket around the ventirad, and we have to drop one of the fixing screws on the horizontal part to be able to slide it further.
I've been using it for a while now, but it's a good accessory, but it's a little short on length at the bracket. Either I'm doing the ventirad, or I'm running into the top fan of my HAF 632 or just in front of the CPU connectors of my 1080 Ti.
A product that keeps its promise, that's what comes out of it.
The installation is simple and ultra modular (must adapt to any type of case), the whole offers a good solidity to the whole CG and ventirad.
Ideal for people carrying their tower for LAN like me.
Hello,
I'm completely dubious about this product. the basic idea is completely intelligent, but I must have missed something ... I have a noctua NH-12UP SE2 and an aorus GTX 1080ti, and apart from putting everything under strain I didn't understand the point ... the brackets used to hold the graphics card clamped it so tightly that I have the impression that it prevented the fans or the contact from being made ... I had some artifacts in games (I just replaced it with a tube under the CG and it's a joke)... or maybe it's because the system to hold the ventirad put it under stress and my processor started to heat up more than usual... I can't wait to take it off the shelf... I've been a customer since 2004 and I think it's the first time I'm sending back a product because I'm not satisfied.
I've been a customer since 2004 and I think it's the first time I've sent a product back because I'm not satisfied with it.
I put two stars because the idea is good, and that it is perhaps me who took it like a sleeve ...
P.S.: sorry if it's written with my feet, but I didn't take the time to make a draft :)
The product is well thought out, efficient, easy to mount after having taken the precaution of thinking about the positioning in its case, supports a GTX Zotac 1080Ti amp extreme core without any problem: no vibration, does not move.
In conclusion: a product that will become indispensable for the maintenance of a CG and relieve the PCie port of the CM
The product was delivered quickly and with instructions for the different lathes and components we may have at home.
In my case:
Case----------------BeQuiet! Silent Base 800
Fans-------------BeQuiet! Dark Rock 3
-Graphics Card--Nvidia GeForce GTX970 Inno3D
The whole thing is now very securely fixed in my tower and those who were able to get the "Dark Rock 3" can be reassured, the rubber cable goes around the fan without disturbing the cooling blades.
On the "GTX 970" the clamps grip the card tightly without disturbing or damaging the surface.
I can take my tower with me on LANs, moves, etc... No more worries about a heavy fan unit :-). And a big thank you to the designers and LDLC.
Conclusion: 5/5
I have an ASUS gtx 1060 on a small Asus CM (Micro-ATX). So I was afraid of the weight of the graphics card. Fortunately this Tilteek FixCard holds the graphics card well. After to mount it by itself, it's not easy if you want to be precise to hold everything well ^^
I remove half a star for assembly. It is so modular that it takes 3 or 4 hands to assemble it without any difficulties of unexpected rotations. But once mounted in my case it doesn't move anymore :) I sleep well for my graphic card. And designed in France :)
I've been using it for a while now, but it's still a good idea to keep it in good condition.)
nice product, well finished and French!
But doesn't fit in a Cooler master Mastercase Pro 5, that's a shame...
It has two rails, to adjust the fit in the case. One rail is too big and the other one is too small, I'm tempted to take out the grinder for this.
I was looking for a tool like this to support my GTX 1080 Ti STRIX OC and it's perfect and it even supports my NH-D15s ventirad the flange goes perfectly around this rad. I was afraid of the weight of these components, but now I'm reassured. I'm not sure if I'm going to be able to use it for a lot of other things, but I'm sure I'll be able to. Nothing to complain about the assembly is easy once you understand the trick it takes about 20 minutes. I strongly recommend it to all those who have heavy rads and graphics cards without hesitation.
I'm not sure if I'm right or wrong, but I'm not sure if I'm right or wrong....
I'm not sure if it's a good idea to have a be quiet Dark Rock PRO 3 and a ZOTAC GeForce GTX 1070 AMP Extreme sli, but it's not working anymore ! when you put the stand against the graphic cards and the fan you can't connect the PSU and when you move it to be able to connect it's the sli bridge that doesn't work anymore ... the thing that really annoys me ...
It is a very well designed product that is easy to install with the help of the installation manual (if in doubt, check out the video in the product sheet). The whole thing looks strong.
I have to say that I'm very happy with this product, but I'm not sure I'm going to be able to get it to work properly, because it's a very good product.
I have to say that I'm very happy with this product.
I don't often comment on a purchase but I have to say that I and several people I know are very satisfied with the LDLC service.
I dialled my pc and forgot to add the assembly, but no worries, a quick call and everything is fine. Assembled and shipped in a timely manner, received in 8 days after payment was received.
A quality service like we would like to see more of. 100% satisfied.
Simple, effective and no-frills product.
Quick installation, just need a crosshead screwdriver to tighten the few screws present to lock the (vertical) slide and the horizontal case support. Placement in the case is simple, and the graphics card (GTX 970 Strix OC) no longer bends the PCIe slot of the motherboard.
NB: I do not use the fan tray.
However, beware of people whose graphics cards are really too big, the power cord of the card can be a problem depending on its placement.
Four stars, because the product is a bit expensive (maybe it's because it's made in France, who knows), and the amount of cardboard could be reduced in the packaging.
The weight of my KFA² GTX 1080 EXOC was a real pain. The transport of my beast was risky for the pcb but since "TILTeek Fix Card" no more fear of breakage.
The advantages: - Fixes the GPU correctly
- No heat transfer
- Good finish
- Lightweight
- Can hold several GPUs
- Fits a lot of cases
The -:- It takes 3 hands to install it (2 to deploy 1 to tighten)
- Price too high for such a part (a 15€ patch would be acceptable, a person who doesn't care about aesthetics will recommend a 10 cents patch that will do the same job.
very useful product for the maintenance of the graphics card gtx 1080 of inno3d and the ventilrad only small thing not very easy to put in place I find but apart from that it makes super well are work
I like :
- the design
- the practical and interesting idea
- can be assembled on its own
I like Less :
- the low rigidity of the materials used
- the system of maintaining the processor fan needs to be REVISED (a simple rubber sheath with a lateral pressure)
- the installation of the vertical rail system (in spite of the instructions) is laborious and can only be done with pressure and force
Very satisfied on the whole, despite some difficulties to fix it. I had to go back several times to tighten all the parts: slides (because they do not touch the ventirad in my case) and flanges/bolts (be careful with the direction which is very important and the distance of one centimetre from the card which is important).
A clever system that I have been dreaming of for years, having a big PC with a big graphics card (ROG Strix 1070 oc) and I sometimes carry it around,
It's a great way to get the most out of your computer.
I'm not sure if it's a good idea or not, but it's a good idea.
the pressurization of the support is crap, I took almost 40 minutes to finish installing it
The same goes for the "CG clamp". It's a great idea.
a worm screw system to clamp the parts in the tower and the CG would have been great
it's really necessary that everything is very well tightened so that nothing moves
once this installation is finished, I am 100% satisfied, everything is fixed in my tower and does not move anymore
product 18/20
assembly 10/20
price a little high, 29.99€ would be more appropriate
overall satisfaction 17/20
The product is well made but impossible to use properly as my case (aerocool xpredator) has a 140mm fan on the top side and it is impossible to position the fixcard vertically.
The product is a great idea for people who have big graphics cards (GTX 980 Ti for example) or big fans. Especially for LAN players who move their PCs all the time.
But there are a few shortcomings:
- the rail that attaches to the top and bottom of the case has to be put in place by hand (i.e. push one rail up and one rail down) while tightening a screw to hold it in place (so you either need three hands or two)
- the fasteners that are supposed to hold the graphics card are not really tight around it, even when I tightened them all the way... annoying
- the fixation to attach the ventirad seems quite inefficient too
So it's a return for me. Be careful, my opinion may depend on my configuration and this product may correspond to your expectations!
Good morning, sir,
Thank you for your feedback on its use.
We are sorry to hear that our product did not give you complete satisfaction.
However, we would like to make a few points that are useful for all users of the patented FixCard fastening system:
- It is important to strictly follow the instructions and assembly steps in the manual provided with the product
- Do not hesitate to watch the "step by step" assembly video included in the product sheet and available at the following address: https://www.youtube.com/watch?v=i0Qt8h0Kx4c
- As for the installation of the rails, they slide easily and can be installed by one person, as shown in the video tutorial at this stage: https://www.youtube.com/watch?v=i0Qt8h0Kx4c&feature=youtu.be&t=2m47s
- It is imperative that the clamps holding the graphics card are positioned exactly as described in the manual. When correctly positioned, they form a "V" shape without being able to rotate, thus blocking the graphics card on both sides (illustration available here: http://media.ldlc.com/bo/images/fiches/accessoire_de_boitier/tilteek/fixcard/fixcard-brides_gpu.jpg). It is essential that this step is followed to ensure that the graphics card does not move.
- The LDLC team of technicians and experts can also advise you on the installation of your FixCard (http://www.ldlc.com/faq/n855/conseils-techniques/ ) if you wish.
All the tests carried out during the design of the product and when it leaves the factory tend to prove the effectiveness of this holding system.
Thank you for your interest in our product and our brand.
Yours faithfully
The TILTeeK team
A product that keeps its promise, that's what comes out of it.
The installation is simple and ultra modular (must adapt to any type of case), the whole offers a good solidity to the whole CG and ventirad.
Ideal for people carrying their tower for LAN like me.
