very well
no maintenance required (apart from dust from the ventirad), works as well as a thermal paw and does not dry out, a little fragile but reusable
no maintenance required (apart from dust from the ventirad), works as well as a thermal paw and does not dry out, a little fragile but reusable
It's very easy to install and cools perfectly.
I'm pleasantly surprised by this product, which is an effective replacement for thermal pasta.
I bought it for a gamer laptop, with the idea of being able to use it and re-use it. First of all, you have to prepare your cut to make sure you don't tear your pad, I'm quite happy with my cut on the GPU, I've got a very good temperature, but for the CPU, I messed up, the pad is torn on one corner, I think that's why I've had bad temperature since
I'm not convinced by the durability aspect, I'll probably have to buy another one to redo the CPU, although I hope to be able to test another brand. I don't think there's enough contact pressure to get good results on a laptop. However, when you install it, I recommend that you fix your pad with a drop of isopropanol so that nothing moves while you're installing your cooling system.
LDLC great for the packaging and delivery time!
The product does the job, even if it's perhaps a little less effective than a thermal paste.
Its big advantage is its durability compared with a paste that dries over time, and the fact that you can reuse it.
I can't say whether the price is right, but the pad works.
Cutting to size requires a clean cutting surface, a ruler and a cutter. I took the time to do this precisely to the size of my CPU. The Pad is not that fragile, but be careful not to make any folds. Positioning on the CPU is easy because the pad can be slid on precisely. The disadvantage is that you then have to place the Ventirad without sliding the pad underneath, but you get there. Once everything is back in place, the heat dissipates as expected.
I was a bit sceptical, but I gave it a try and I have to say that I'm pleasantly surprised. it's perfect. When putting it in place, be careful because it slips easily. After tightening, no worries. In my opinion, I recommend it.
I didn't really believe in it, but I've got a lot of fingers on each hand, so it's hard to get the thermal paste through effectively. With this pad, the solution to all my worries, the right thickness everywhere at once, a gain of around 20° (from scratch), I'm delighted. And all with LDLC service, as it should be!
1/ Very easy to install (there's even a well-translated mini-doc). This pad avoids the worry of thermal paste, without bubbles, not too much, not too little....
2/ Seems to be ultra efficient.
I swapped my original small radiator with uncertain thermal paste for a large radiator + this pad.
The result in very intensive use 12core/12 at 100% during 10 min the CPU passes from 94° to 70°!
I will never use thermal paste again,
(see you in a year to check that the quality is still there, I'll add a comment...)
The product may seem expensive at first, but in the end it is worth it.
Indeed, this product is much more efficient than thermal paste. I lost about 10 degrees on a thermal paste that had just been changed. In short, this product is a good investment that I recommend.
I was a bit apprehensive about the application of this paste. In the end, it went well.
I bought the large size for my laptop. I was able to put it on the processor, the graphics chip and the surrounding chips.
It's 29 degrees in my room and I like it, but my laptop doesn't. So I combined this dough with a new one. So I combined this paste with a ventilated stand. I raised the PC and made a hole in the shell.
If it continues to make noise, I will switch to apple with a windows emulator.
Hello everyone, I bought this patch in February. Why so long to wait?
Well my Ryzen 5600X well spread against my MSI liquid 360R system was holding up well to 87° until yesterday morning. More intense use in the last few weeks and games that "lag" have made me do a stress tool that has reached 95°. I go ahead and clean the contacts well with nail polish remover. And cleanly apply the thin Carbonaut film. Reparametrization Bios, optimization of the fans and hop! Windows 10. Result of the stress test: 78° on average with "peaks" at 81°. Well, product validated!
I'll update my review if there are any problems over time. Thank you for your feedback.
I've been using it for a while now and it's been a great help to me in getting my CPU to run smoothly. Very quick and easy to install, compatible with Am4 sockets and all other smaller ones. This size thermal pad is just the right size for a common processor like a Ryzen 7 or 5 and if you have a smaller processor you can cut the carbon pad to the size you want. Ideal for those who don't want to have to change their thermal pad every 6 months. It's supposed to be reusable but I haven't had the chance to disassemble it yet. I recommend it for the price ;)